SARK UCS/MVP Telephony Card Definitions

selsniff & selautosniff - SAIL's device sniffer

Important NOTE!

Selsniff has been deprecated in SAIL-2.1.11-143. It is still present in the release but there is also a new routine called selautosniff which needs no user input to detect and configer TDM4xx class boards and X100P? boards. If your SAIL release is -143 or higher then you need do nothing at all, everything is handled automatically. However, this routine will ONLY handle TDM and X100P? boards. For ISDN BRI you need 2.1.12 or higher.

selsniff - SAIL's pre -143 device sniffer

X100P? 's are configured totally automatically, however TDM400's need some input from you. The routine will ask you to provide details of the FXO/FXS daughterboards fitted to your card. Here is the output from a system with a TDM11b and X100P? card fitted....

[root@test7 selintra]# perl /etc/selintra/selsniff

modprobing for Telephony boards - do a restart if this hangs....

Finished Probes...

        2 Telephony  board(s) found -
        Press "Y" to configure ..
        Removing existing config (if any).....
        Deleted record 1
        Deleted record 2
        Deleted record 5080
        Deleted record Zap4-1
        Deleted record Zap5-1


        processing for board 1


        SUMMARY of BOARD in SLOT 1

         Span 1: WCTDM/0 "Wildcard TDM400P REV E/F Board 1"

                   1 WCTDM/0/0 FXOKS (In use)
                   2 WCTDM/0/1
                   3 WCTDM/0/2
                   4 WCTDM/0/3 FXSKS (In use)




        For each TDM channel, please enter type ...
        By default, TDM channels are setup with Kewlstart. If you
        need to run loopstart or groundstart contact us at www.selintra.com
        *NOTE* - Channel 1 on the TDM400 is furthest from the motherboard

        *HINT* - For extensions enter '2'(FXS), for lines enter '3'(FXO)


                Channel 1
                Channel Type?
                 No Module on this channel...... 1
                 FXS? .......................... 2
                 FXO? .......................... 3
                 FXS Module fitted

                Channel 2
                Channel Type?
                 No Module on this channel...... 1
                 FXS? .......................... 2
                 FXO? .......................... 3
                 No Module fitted

                Channel 3
                Channel Type?
                 No Module on this channel...... 1
                 FXS? .......................... 2
                 FXO? .......................... 3
                 No Module fitted

                Channel 4
                Channel Type?
                 No Module on this channel...... 1
                 FXS? .......................... 2
                 FXO? .......................... 3
                 FXO Module fitted


        processing for board 2


        SUMMARY of BOARD in SLOT 2

         Span 2: WCFXO/0 "Generic Clone Board 1" RED

                   5 WCFXO/0/0 FXSKS (In use)


        X100P has been auto-configured


Probe ends...

Rebuilding Asterisk configuration....
Done

On-board channel summary follows:-

Zaptel Configuration
======================


Channel map:

Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)
Channel 05: FXS Kewlstart (Default) (Slaves: 05)

3 channels configured.


Asterisk PBX Board Probe and Configure: complete

-- AelintraLimited - 28 Jun 2006